COVERAGE CALCULATORS

Coverage rates are approximate and may vary depending on surface porosity, texture, application method and prior coating applications. Because of this it is always recommended to round up to the next gallon or box qty to ensure enough material on hand.

POLYASPARTICS
POLYKOAT GL 70
POLYKOAT GL 80
POLYKOAT GL 85 XTRA SLOW
POLYKOAT GL 90 LVLP
POLYKOAT GL 100
POLYKOAT PRIME 100
FLAKES
POLYURETHANES
60 ALIPHATIC URETHANE
POLY 250 ACRYLIC POLYURETHANE
6000 WB GLOSS URETHANE
6100 WB MATTE URETHANE
MCU 55
MCU 85 NO ODOR URETHANE

EPOXY COATINGS
FAST BASE 360 EPOXY
1040 BONDKOAT WB EPOXY
MAXX FLOW 100% SOLIDS EPOXY
250 HP CYCLO 100% SOLIDS EPOXY
MVB 100 MOISTURE VAPOR BARRIER
EXTRA CLEAR EPOXY
HIGH BUILD EPOXY

SEALERS, WATER REPELLENTS, CURES & MORE.

CURING & CURE & SEALS
REPEL CURE 309
2500 LV UV
CURE 309
CURE & SEAL 30
AQUA CURE 15
AQUA CURE 18
AQUA CURE 21
AQUA CURE 25
AQUA CURE 30
EXPOSED AGGREGATE
AGGRESEAL SUPREME
AGGRESEAL SUPREME 350 VOC
AGGRESOL-S
AGGRESOL-F
SURFACE AID
DECORATIVE SEALERS
DECO GUARD
DECO GUARD PLUS
DECO GUARD PLUS 700
DECO GUARD WB
2000 SUPREME
STAMP SEAL
STAMP SEAL GLOSS
STAMP SEAL XTREME GLOSS
LUSTER SHIELD
SUPER LUSTER SHIELD
STAMP SEAL CONCENTRATE
INFUSION 44
INFUSION 44 GLOSS

INDUSTRIAL FLOOR WAXES
CHERRY WAX
CHERRY WAX MATTE

LOW VOC SEALERS
2000 SUPREME 400 VOC
STAMP SEAL GLOSS 400 VOC
STAMP SEAL XTREME GLOSS 400 VOC
LUSTER SHIELD SATIN
LUSTER SHIELD 350 VOC
SUPER LUSTER SHIELD 350 VOC
STAMP SEAL CONCENTRATE 400 VOC
PAVER SEALERS
PAVER SHIELD
PAVER SHIELD 400 VOC
PAVER SHIELD WB
ENHANCER SHIELD SB
WATER REPELLENTS
HOLD OUT
SURFBLOCK WB 75
SURFBLOCK SB 12
SURFBLOCK SB 12 - 250 VOV
SURF-GUARD SB 20
SURF-GUARD SB 40
SURF-GUARD SB 100

POLISHING
AQUALON S 400
AQUALON SP 450
AQUALON L 100
AQUALON NANO GUARD
AQUALON STAIN GUARD
MISCELLANEOUS PRODUCTS
ANTIQUE LIQUID RELEASE

Maxx Flow Epoxy Tech data sheet COVERAGE RATE: First Coat - Direct to Concrete : 100 - 150 ft² per gallon* Second Coat - Over Existing Coating : 75 - 125 ft² per gallon* Metallic Coat - Over Existing Coating : 40 - 100 ft² per gallon* APPLICATION: It is suggested to apply the mixed material by pouring it out onto the surface and spread with a flat flexible squeegee or a notched squeegee. Use a 1/8” (8 - 12 mil) notched squeegee when applying direct to concrete. A 3/16” (15 - 20 mil) to 1/4” (25 - 30 mil) notched squeegee may be used on additional coats over a completely sealed off surface. Back roll clear and solid color epoxy using 3/8” nap shedless roller or 3/8” foam roller. 18” rollers are recommended for any surface to speed up application time and reduce roller marks. For metallic applications, refer to Metallic FX data sheet for more information.

Polykoat GL 80 tds application: COVERAGE RATE: First Coat - Direct to Concrete : 200 - 300 ft² per gallon* Second Coat - Over Existing Coating : 250 - 350 ft² per gallon* Over Media Broadcast Systems : 100 - 175 ft² per gallon* *Coverage rates may vary depending upon surface porosity, texture, media size, application method and prior coating application. Excessive build up should be avoided. APPLICATION: OVER SMOOTH SURFACES: Using a brush and/or 3/8” nap shedless roller, dip and roll the mixed material from a roller pan. 18” rollers are recommended for any surface to speed up application time and reduce roller marks. Start by placing the wet roller at one corner of an approximate 4’ x 4‘ square and roll the material at an angle to opposite corner applying no pressure to the roller. Spread the material across only that square and immediately back-roll to even out material and roller lines.

250 HP Epoxy APPLICATION: Immediatly pour mixed onto the surface! It is suggested to apply the mixed material by pouring it out onto the surface and spread with a flat flexible squeegee or a notched squeegee. Use a 1/8” (8 - 12 mil) notched squeegee when applying direct to concrete. A 3/16” (15 - 20 mil) notched squeegee may be used on additional coats over a completely sealed off surface. Back roll clear and solid color epoxy using 3/8” nap shedless roller or 3/8” foam roller. 18” rollers are recommended for any surface to speed up application time and reduce roller marks. For metallic applications, refer to Metallic FX data sheet for more information. Use a brush or small roller for corners and areas hard to maneuver longer squeegees/rollers. While applying keep a wet edge to prevent roller marks. It is recommended to work in sections usually using control joints as dividers to ensure proper application results.

6000 WB Gloss urethane tds APPLICATION: Using a brush and/or 3/8” nap shedless roller, dip and roll the mixed material from a roller pan. 18” rollers are recommended for any surface to speed up application time and reduce roller marks. Start by placing the wet roller at one corner of an approximate 4’ x 4‘ square and roll the material at an angle to opposite corner applying no pressure to the roller. Spread the material across only that square and immediately back-roll to even out material and roller lines. Adjust the size of your square as needed based on the amount of material being applied with the roller. After finishing the square, move on to the next square using the same technique.

PolyKoat GL 85 SLOW tech data sheet COVERAGE RATE: First Coat - Direct to Concrete : 200 - 300 ft² per gallon* Second Coat - Over Existing Coating : 250 - 350 ft² per gallon* Over Media Broadcast Systems : 100 - 175 ft² per gallon* APPLICATION: OVER SMOOTH SURFACES: Using a brush and/or 3/8” nap shedless roller, dip and roll the mixed material from a roller pan. 18” rollers are recommended for any surface to speed up application time and reduce roller marks. Start by placing the wet roller at one corner of an approximate 4’ x 4‘ square and roll the material at an angle to opposite corner applying no pressure to the roller. Spread the material across only that square and immediately back-roll to even out material and roller lines.

OPTIMUS LINE
OPTIMUS-XTC
OPTIMUS BASE-CS
OPTIMUS BASE-DTC
OPOPT

EN ESPAÑOL TDS

VOC MAP

CLICK FOR TDS

Concrete curing compound made in the usa and meets astm 309 specs with water repellent features also.

American made stamped concrete sealer, Excellent long lasting gloss compared to other acrylic sealers.

Made in the usa, low viscosity uv stable decorative concrete sealer available near me with nationwide shipping.

Top rated usa made concrete sealer. Perfect for many different types of concrete, new or old. Excellent salt and water resistance.

Top rated american made exposed aggregate concrete sealer made by SurfKoat

American made water repellents available from Surfkoat concrete coatings manufacturer. Surfblock wb 75

COVERAGE CALCULATORS

POLYASPARTICS POLYKOAT GL 70 POLYKOAT GL 80 POLYKOAT GL 85 XTRA SLOW POLYKOAT GL 90 LVLP POLYKOAT GL 100 POLYKOAT PRIME 100 FLAKES POLYURETHANES 60 ALIPHATIC URETHANE POLY 250 ACRYLIC POLYURETHANE 6000 WB GLOSS URETHANE 6100 WB MATTE URETHANE MCU 55 MCU 85 NO ODOR URETHANE

EPOXY COATINGS FAST BASE 360 EPOXY 1040 BONDKOAT WB EPOXY MAXX FLOW 100% SOLIDS EPOXY 250 HP CYCLO 100% SOLIDS EPOXY MVB 100 MOISTURE VAPOR BARRIER EXTRA CLEAR EPOXY HIGH BUILD EPOXY

SEALERS, WATER REPELLENTS, CURES & MORE.

INDUSTRIAL FLOOR WAXES CHERRY WAX CHERRY WAX MATTE

POLISHING AQUALON S 400 AQUALON SP 450 AQUALON L 100 AQUALON NANO GUARD AQUALON STAIN GUARD MISCELLANEOUS PRODUCTS ANTIQUE LIQUID RELEASE

OPTIMUS LINE OPTIMUS-XTC OPTIMUS BASE-CS OPTIMUS BASE-DTC OPOPT

send orders to: orders@surfkoat.com

POLYASPARTICS
POLYKOAT GL 70
POLYKOAT GL 80
POLYKOAT GL 85 XTRA SLOW
POLYKOAT GL 90 LVLP
POLYKOAT GL 100
POLYKOAT PRIME 100
FLAKES
POLYURETHANES
60 ALIPHATIC URETHANE
POLY 250 ACRYLIC POLYURETHANE
6000 WB GLOSS URETHANE
6100 WB MATTE URETHANE
MCU 55
MCU 85 NO ODOR URETHANE

EPOXY COATINGS
FAST BASE 360 EPOXY
1040 BONDKOAT WB EPOXY
MAXX FLOW 100% SOLIDS EPOXY
250 HP CYCLO 100% SOLIDS EPOXY
MVB 100 MOISTURE VAPOR BARRIER
EXTRA CLEAR EPOXY
HIGH BUILD EPOXY

INDUSTRIAL FLOOR WAXES
CHERRY WAX
CHERRY WAX MATTE

POLISHING
AQUALON S 400
AQUALON SP 450
AQUALON L 100
AQUALON NANO GUARD
AQUALON STAIN GUARD
MISCELLANEOUS PRODUCTS
ANTIQUE LIQUID RELEASE

OPTIMUS LINE
OPTIMUS-XTC
OPTIMUS BASE-CS
OPTIMUS BASE-DTC
OPOPT